پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 161 |
| تعداد شماره‌ها | 6,532 |
| تعداد مقالات | 70,504 |
| تعداد مشاهده مقاله | 124,122,816 |
| تعداد دریافت فایل اصل مقاله | 97,231,030 |
پالایش و بازیابی روغن‌های آلوده به PCBs به روش شیمیایی (مطالعۀ موردی: نیروگاه بعثت تهران) | ||
| محیط شناسی | ||
| مقاله 14، دوره 41، شماره 3، مهر 1394، صفحه 681-693 اصل مقاله (1.27 M) | ||
| نوع مقاله: مقاله پژوهشی | ||
| شناسه دیجیتال (DOI): 10.22059/jes.2015.55905 | ||
| نویسندگان | ||
| فاطمه اکبرپور سراسکان‌رود1؛ علیرضا نورپور* 2؛ امیر ناصر ملک قاسمی3 | ||
| 1کارشناسی ارشد شیمی خاک و کارشناس مسئول آلودگی آب و خاک، ادارۀ کل حفاظت محیط‌زیست استان تهران، | ||
| 2دانشیار دانشکدۀ محیط‌زیست دانشگاه تهران، دکتری مهندسی مکانیک سیالات، گروه مهندسی محیط‌زیست | ||
| 3مهندس شیمی، مدیر پروژۀ شرکت پردیس کیش | ||
| چکیده | ||
| ترکیبات PCB، ترکیباتی با سمیت بالا در محیط‌زیست‌اند، که به واسطۀ نگرانی‌های ناشی از آثار ناخوشایند این ترکیبات در محیط و پایداری آن‌ها، تولید، استفاده و واردات آن در برخی کشورها ممنوع شده است. استفادۀ گسترده از این ترکیبات در تجهیزات صنعتی سبب ایجاد مخاطرات زیست‌محیطی و به‌رغم ممنوعیت کنوانسیون استکهلم مبنی بر استفاده از این ترکیبات تا سال 2025، مقادیر زیادی از این ترکیبات در صنعت برق کشور انبار شده است. در این پژوهش 74000 لیتر از روغن‌های PCBs نیروگاه بعثت تهران با آلودگی زیر ppm10000 با روش شیمیایی پایۀ فلز سدیم امحا شد. در ترانسفورمرهای مورد تحقیق، عمدتاً از سه نوع PCB آرکولار 1242، 1254، 1260 استفاده شده بود که پس از فرایند امحا، میزان PCBs به روش کروماتوگرافی گازی سنجش شد. کاهش میزان PCBs تا ppm2 و کمتر از آن نشان‌دهندۀ توفیق روش شیمیایی با پایۀ سدیم در امحای روغن‌های PCBs است. پس از کاهش میزان آلودگی، روغن‌ها وارد فرایند احیای مجدد شده و نمونه‌ها برای انجام آزمایش‌های شیمیایی، فیزیکی، HSE و الکتریکی به آزمایشگاه فرستاده شدند. نتایج آزمایش‌ها نشان داد که روغن‌های احیا‌شده از کیفیت استاندارد IEC60296 برخوردارند. | ||
| کلیدواژه‌ها | ||
| بازیابی؛ PCBs؛ روش شیمیایی؛ کنوانسیون استکهلم؛ نیروگاه بعثت | ||
| عنوان مقاله [English] | ||
| Treatment and Regeneration of PCBs in Transformer Oil by a Chemical Process (Case Study: Tehran Besat Power Plant) | ||
| نویسندگان [English] | ||
| Fatemeh Akbarpour saraskanroud1؛ Ali Reza Noorpoor2؛ Amir Naser Malekghasemi3 | ||
| 1MSc Graduated, Soil & Water Pollution Supervisor, Tehran Province DOE | ||
| 2Associate Professor, Graduate Faculty of Environment, University of Tehran. | ||
| 3Chemistry Engineer, Pardis Kish Company Manager | ||
| چکیده [English] | ||
| Introduction PCBs belong to a broad family of man-made organic chemicals known as chlorinated hydrocarbons. They have a range of toxicity and vary in consistency from thin, light-colored liquids to yellow or black waxy solids. Due to their non-flammability, chemical stability, high boiling point, and electrical insulating properties, PCBs were used in hundreds of industrial and commercial applications including electrical, heat transfer, and hydraulic equipment; as plasticizers in paints, plastics, and rubber products; in pigments, dyes, and carbonless copy paper; and many other industrial applications.PCB (or PCBs) is a category, or family, of chemical compounds formed by the addition of Chlorine (Cl2) to Biphenyl (C12H10), which is a dual-ring structure comprising two 6-carbon Benzene rings linked by a single carbon-carbon bond. Polychlorinated biphenyl, commonly referred to as PCB, was in widespread use as a dielectric fluid due to its special physical and chemical properties. Since then, PCBs have developed a notorious reputation due to their potential for environmental contamination and for their potential to react to form other, highly toxic substances. Under incomplete combustion, PCBs can form products such as furans and dioxins. Due also to the stability of PCB and its potential for environmental accumulation and harm. Many different process can and have been used to destroy PCBs, but each has its limitations and potential risks. High temperature incineration has been widely used, but has the inherent risk that if inadequate temperatures are attained at the point of destruction of the PCB, dioxins and furans can be formed. Another dechlorination process is the gas-phase reduction, in which the main difference is the chemical used as reducing reagents. The molten salt process has been used on a small scale since 1950 [9]. In the process, a bed of alkaline molten salt, usually sodium carbonate oxidizes organic materials. Any chlorine, sulfur, phosphorous, or ash products in the feed are converted to inorganic salts and retained in the salt bed. This process cannot treat soils and other materials with a high content of inert material. With bench and pilot scale systems, PCBs was destroyed in molten sodium carbonate/sodium chloride with efficiencies of 99.99 Percent. Destruction efficiency with chlordane was apparently not determined. Indeed, the use of performance measures, "destruction efficiency" and DRE, in describing the performance of this technology suggests that one may have been used inaccurately. i.e., destruction efficiency can be determined only if all process residues are analyzed for the presence of undestroyed chemicals of concern. * Corresponding Author: Tel: +98 (21) 66468009 Email: noorpoor@ut.ac.ir Materials & Methods: Chemical dehalogenation (or dechlorination) is a chemical process used to remove halogens (usually chlorine) from a chemical contaminant by hydrogen or a reducing radical containing hydrogen donor. In the case of based catalyzed dechlorination, the process key is the hydrogen donor with an oxidation potential low enough to produce nucleophilic hydrogen in the presence of base Na+. On the other hand, for the Eco-Logic process gaseous hydrogen at high temperature is the reducing reagent to destroy chlorinated organic compounds. Chemical dehalogenation technologies are applicable to halogenated aromatic compounds, including PCBs, PCDDs, PCDFs, …. Treated transformer oil was segregated from the contents (Fig.1.). Figure 1- PCB Destruction Flow Chart Results and Discussion: In this study a practical and efficient disposal dechlorination process has been reported for Tehran Besat Power Plant PCBs less than 10000 ppm. The transformer oil containing commercial PCB mixtures (Aroclor 1242, 1254 and 1260) was treated by chemical process. 74000 lit (666000Kg) of PCBs oil (less than 7000 ppm) from Tehran Besat power plant sent to site plan. Content of 4 transformer oil samples is reported in Fig.2. Results of PCB content of transformer oil sample. The diluted is cleaned with solvent and then analyzed by a capillary Gas Chromatograph with an electron capture detector for the detection of PCBs. Results are reported as mg of PCB per liter of oil (ppm). Samples containing less than 2 mg/l PCB will be reported as Figure.2- Tehran Besat Power Plant PCBs waste less than 7000 ppm Conclusions: The destruction and removal efficiency of PCBs was 99.99% and/ or less than 2 ppm. After destruction, the reactor content was drained. The treated transformer oil was segregated from the contents by filtering, washing, dehydrating under vacuum. Such segregation steps described standard treatment of treated transformer oil before reuse. Treated transformer oil passed IEC60296 (oil quality standard). We have developed a safe, inexpensive and efficient chemical dechlorinating process for the disposal of Besat Plant PCBs directly in transformer oil. Disposal/decontamination of slightly PCB contaminated transformer oils could be established in Iran quite rapidly if decisions and resources can be secured. A destruction and removal of PCBs in Transformer Oil by a Chemical Process is one of the commercial technologies. Considerable PCB issue in Iran and firm steps needs to be taken in order to avoid releases in the environment from inappropriate waste management or spillage. | ||
| کلیدواژه‌ها [English] | ||
| Polychlorinated biphenyls, Stockholm convention, Regeneration, Chemical process, Besat Power Plant | ||
| مراجع | ||
|
برنامۀ اقدام ملی ایران NIP، 2005. Borja., J., Taleon., D.M., Auresenia, J., Gallardo, S. 2005. Polychlorinated biphenyls and their biodegradation. Process Biochemistry, 40(6):1999-2013.
Cafissi, A., Beduschi, S., Balacco, V., Trasatti, S.2007. Chemical dechlorinating of polychlorinated biphenyls (PCBs) from dielectric oils. Environmental chemistry letters, 5(2):101-106.
Jones, D.A., Lelyveld, T.P., Marvofidis, S.D., Kingman, S.W., Miles, N.J.2003. Microwave Heating Applications in Environmental Engineering- a review. Resources conservation and Recycling, 34: 75-90.
Kastank, P., Kastank, F., Hajek, M., Sobek, J., Solcova, O.2011. Dehalogenation of polychlorinated biphenyls (PCB) by nucleophile reactants at the presence of ionic liquids and under application of microwaves. Global NEST Journal.
Liu, X., Zhao, K., Sun, K., Zhang, G., Zaho, Y. 2011. Dechlorination of PCBs in the simulative transformer oil by microwave- hydrothermal reaction with zero-valent iron involved. Chemosphere, 82(5):773-777.
Manzano, M.A., Perales, J.A., Sales, D., Quiroga, J.M. 2004. Using solar and ultraviolet light to degrade PCB in sand and transformer oils. Chemosphere, 57: 645- 654.
Sang Ryoo, K., Hyuk Byun, S., Choi, J., Pyo Hong,Y., Tae Ryu, Y., Seol Song, J., Suk Lee, D., Sung Lee, H. 2007. Destruction and removal of PCBs in waste transformer oil by a chemical dechlorination process. Bull. Korean Chem. SOC, 28(4):520-528.
UNEP. 2004. The technical guidelines on the environmentally sound management of waste consisting of containing or contamination with polychlorinated tetraphenyl (PCT), and polybrominated biphenyls.
Wiegel, J., Wu, Q. 2000. Microbial reductive dehalogenation of polychlorinated biphenyls. FEMS microbiol, 32:1-15.
Wong, KH., Wong, PK. 2006. Degradation of polychlorinated Biphenyls by UV Catalyzed Photolysis. Human and Ecological Risk Assessment, 12(2): 259-269.
Woodyard, J.P., King, J.J. 1992. PCB Management handbook: Executive Enterprises Publications Company.
Wu, W., Xu, J., Zhao, H., Zhang, Q., Liao, S. 2005. A practical approach to the degradiation of polychlorinated biphenyls in transformer oil. Chemosphere, 60(7):944-950
Zorrilla Velazco, M., Velazco Pedroso, P., Villanueva Ramos, G., Van Langenhove, H. 2013. Chemical dechlorination for the treatment of PCBs present in transformer oil (Sovtol-10): Parameter Study. | ||
|
آمار تعداد مشاهده مقاله: 2,235 تعداد دریافت فایل اصل مقاله: 1,413 |
||