پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 158 |
| تعداد شمارهها | 6,225 |
| تعداد مقالات | 67,692 |
| تعداد مشاهده مقاله | 115,003,655 |
| تعداد دریافت فایل اصل مقاله | 89,683,147 |
Subcooled two-phase flow boiling in a microchannel heat sink: comparison of conventional numerical models | ||
| Journal of Computational Applied Mechanics | ||
| مقاله 4، دوره 51، شماره 1، شهریور 2020، صفحه 37-45 اصل مقاله (905.9 K) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22059/jcamech.2019.285994.417 | ||
| نویسندگان | ||
| Ali Soleimani؛ Pedram Hanafizadeh* ؛ Amirmohammad Sattari | ||
| School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran | ||
| چکیده | ||
| Subcooled flow boiling in multi-microchannels can be used as an efficient thermal management approach in compact electrical devices. Highly subcooled flow boiling of HFE 7100 is studied in two microchannel heat sinks to choose a proper numerical model for simulating boiling flows in microchannels. Results of five different numerical models, including Volume of Fluid (VOF), Eulerian boiling, Eulerian Lee, Eulerian thermal phase change, and mixture models, were compared with experimental data. ANSYS Fluent was used as the numerical tool to solve three-dimensional governing equations. Results were obtained in the steady-state condition of the transient solution. The average wall temperature reached a steady state in all models except in Eulerian boiling and mixture models. It was found that Eulerian thermal phase change and VOF models predicted microchannel’s bottom wall average temperature with less than 2% error. VOF model predicted flow boiling regime as it was reported in the experimental research and boiling curves. Velocity distribution over microchannel height was investigated, and it was observed that after the onset of nucleate boiling, the velocity profile becomes asymmetrical. Also, in the two-phase regions, each phase had a different velocity magnitude and distribution. Based on flow regime and temperature results, which were compared with experimental data, VOF model was recommended as the best model to simulate flow boiling in microchannels at the working conditions of this research. Furthermore, subcooled flow boiling’s capability to be used in thermal management systems was proved while observing temperature distribution over computational domain. | ||
| کلیدواژهها | ||
| Subcooled flow boiling؛ Microchannel؛ Heat sink؛ CFD؛ VOF model | ||
| مراجع | ||
|
[1] D. B. Tuckerman and R. F. W. Pease, “High-performance heat sinking for VLSI,” IEEE Electron Device Lett., vol. 2, no. 5, pp. 126–129, May 1981.
[2] C. L. Ong and J. R. Thome, “Macro-to-microchannel transition in two-phase flow: Part 1 – Two-phase flow patterns and film thickness measurements,” Exp. Therm. Fluid Sci., vol. 35, no. 1, pp. 37–47, Jan. 2011.
[3] G. Karniadakis, A. Beskok, and N. Aluru, Microflows and Nanoflows, vol. 29. New York: Springer-Verlag, 2005.
[4] M. Hatami and D. D. Ganji, “Thermal and flow analysis of microchannel heat sink (MCHS) cooled by Cu–water nanofluid using porous media approach and least square method,” Energy Convers. Manag., vol. 78, pp. 347–358, Feb. 2014.
[5] B. H. Salman, H. A. Mohammed, K. M. Munisamy, and A. S. Kherbeet, “Characteristics of heat transfer and fluid flow in microtube and microchannel using conventional fluids and nanofluids: A review,” Renew. Sustain. Energy Rev., vol. 28, pp. 848–880, Dec. 2013.
[6] A. K. M. M. Morshed, F. Yang, M. Yakut Ali, J. A. Khan, and C. Li, “Enhanced flow boiling in a microchannel with integration of nanowires,” Appl. Therm. Eng., vol. 32, no. 1, pp. 68–75, Jan. 2012.
[7] T. Harirchian and S. V. Garimella, “Flow regime-based modeling of heat transfer and pressure drop in microchannel flow boiling,” Int. J. Heat Mass Transf., vol. 55, no. 4, pp. 1246–1260, Jan. 2012.
[8] B. Agostini, J. R. Thome, M. Fabbri, B. Michel, D. Calmi, and U. Kloter, “High heat flux flow boiling in silicon multi-microchannels – Part I: Heat transfer characteristics of refrigerant R236fa,” Int. J. Heat Mass Transf., vol. 51, no. 21–22, pp. 5400–5414, Oct. 2008.
[9] P. C. Lee and C. Pan, “Boiling heat transfer and two-phase flow of water in a single shallow microchannel with a uniform or diverging cross section,” J. Micromechanics Microengineering, vol. 18, no. 2, p. 025005, Feb. 2008.
[10] J. Lee and I. Mudawar, “Fluid flow and heat transfer characteristics of low temperature two-phase micro-channel heat sinks – Part 1: Experimental methods and flow visualization results,” Int. J. Heat Mass Transf., vol. 51, no. 17–18, pp. 4315–4326, Aug. 2008.
[11] G. Oguntala, R. Abd-alhameed, G. Sobamowo, and I. Danjuma, “Performance, thermal stability and optimum design analyses of rectangular fin with temperature-dependent, thermal properties and Internal heat generation,” vol. 49, no. 1, pp. 37–43, 2018.
[12] A. Alizadehdakhel, M. Rahimi, and A. A. Alsairafi, “CFD modeling of flow and heat transfer in a thermosyphon,” Int. Commun. Heat Mass Transf., vol. 37, no. 3, pp. 312–318, Mar. 2010.
[13] Y. W. Kuang, W. Wang, R. Zhuan, and C. C. Yi, “Simulation of boiling flow in evaporator of separate type heat pipe with low heat flux,” Ann. Nucl. Energy, vol. 75, pp. 158–167, Jan. 2015.
[14] E. Abedini, A. Behzadmehr, S. M. H. Sarvari, and S. H. Mansouri, “Numerical investigation of subcooled flow boiling of a nanofluid,” Int. J. Therm. Sci., vol. 64, pp. 232–239, Feb. 2013.
[15] I. Behroyan, P. Ganesan, S. He, and S. Sivasankaran, “CFD models comparative study on nanofluids subcooled flow boiling in a vertical pipe,” Numer. Heat Transf. Part A Appl., vol. 73, no. 1, pp. 55–74, Jan. 2018.
[16] A. Mukherjee and S. G. Kandlikar, “Numerical simulation of growth of a vapor bubble during flow boiling of water in a microchannel,” Microfluid. Nanofluidics, vol. 1, no. 2, pp. 137–145, May 2005.
[17] A. Mukherjee, S. G. Kandlikar, and Z. J. Edel, “Numerical study of bubble growth and wall heat transfer during flow boiling in a microchannel,” Int. J. Heat Mass Transf., vol. 54, no. 15–16, pp. 3702–3718, Jul. 2011.
[18] M. Magnini, B. Pulvirenti, and J. R. Thome, “Numerical investigation of hydrodynamics and heat transfer of elongated bubbles during flow boiling in a microchannel,” Int. J. Heat Mass Transf., vol. 59, no. 1, pp. 451–471, Apr. 2013.
[19] C. Fang, M. David, A. Rogacs, and K. Goodson, “VOLUME OF FLUID SIMULATION OF BOILING TWO-PHASE FLOW IN A VAPOR-VENTING MICROCHANNEL,” Front. Heat Mass Transf., vol. 1, no. 1, Jun. 2010.
[20] R. Zhuan and W. Wang, “Flow pattern of boiling in micro-channel by numerical simulation,” Int. J. Heat Mass Transf., vol. 55, no. 5–6, pp. 1741–1753, Dec. 2011.
[21] R. Zhuan and W. Wang, “Simulation of subcooled flow boiling in a micro-channel,” Int. J. Refrig., vol. 34, no. 3, pp. 781–795, May 2011.
[22] ANSYS FLUENT, “User’s Guide (Release 18.2).” ANSYS Inc, 2017.
[23] W. H. Lee, “A pressure iteration scheme for two-phase modeling,” Los Alamos Sci. Lab. Los Alamos, New Mex. Tech. Rep. LA-UR, pp. 79–975, 1979.
[24] N. Kurul, “On the modeling of multidimensional effects in boiling channels,” ANS. Proc. Natl. Heat Transf. Con. Minneapolis, Minnesota, USA, 1991, 1991.
[25] V. I. Tolubinsky and D. M. Kostanchuk, “Vapour bubbles growth rate and heat transfer intensity at subcooled water boiling,” in International Heat Transfer Conference 4, 1970, vol. 23.
[26] M. Misale, G. Guglielmini, and A. Priarone, “HFE-7100 pool boiling heat transfer and critical heat flux in inclined narrow spaces,” Int. J. Refrig., vol. 32, no. 2, pp. 235–245, Mar. 2009. | ||
|
آمار تعداد مشاهده مقاله: 1,270 تعداد دریافت فایل اصل مقاله: 811 |
||