پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 161 |
| تعداد شماره‌ها | 6,532 |
| تعداد مقالات | 70,500 |
| تعداد مشاهده مقاله | 124,090,009 |
| تعداد دریافت فایل اصل مقاله | 97,193,711 |
Performance Improvements of a Centrifugal Pump with Different Impellers using Polymer Additive | ||
| Journal of Computational Applied Mechanics | ||
| مقاله 5، دوره 48، شماره 2، اسفند 2017، صفحه 199-206 اصل مقاله (913.31 K) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22059/jcamech.2017.234895.150 | ||
| نویسندگان | ||
| Alireza Riasi* ؛ Farzin Dianatipoor | ||
| School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran. | ||
| چکیده | ||
| In this study, the performance of a centrifugal pump is investigated by adding polyacrylamide (PAM) polymer over the working fluid which is tap water in this case. PAM is a long chain polymer that leads to reduce the wall shear stress and drag in a turbulent fluid. Three different blade profiles including radial, straight backward and circular backward have been examined. For this purpose, a centrifugal pump test rig consists of reservoir, pump-motor, volumetric measuring tank, pressure gauges, speed control, and motor dynamometer has been used. Different concentrations of PAM polymer solution are prepared in the range of 80-240 ppm of PAM. The results show that the maximum amount of relative efficiency is approximately 3% for the radial propeller, 13% for the straight backward propeller, and 18% for the circular backward which is occurs at 160 ppm of PAM. It is found that this increase is more pronounced in the case of circular backward impeller. Moreover, in the case of radial blade profile, it is observed that in spite of efficiency increase, the head decreases at low flow rate with adding PAM. | ||
| کلیدواژه‌ها | ||
| drag reduction؛ water pumps؛ Polyacrylamide polymer؛ Efficiency؛ blade geometry | ||
|
سایر فایل های مرتبط با مقاله
|
||
| مراجع | ||
|
[1] Bidhandi, M. E., Riasi, A., & Ashjaee, M. (2014). The influence of SiO 2 nanoparticles on cavitation initiation and intensity in a centrifugal water pump. Experimental Thermal and Fluid Science, 55, 71-76.
[2] AbuYousef, I. A., Olson, J. A., Martinez, D. M., & Green, S. (2010, January). Pumping Performance Increase through the Addition of Turbulent Drag-Reducing Polymers to Pulp Fibre Suspensions. In ASME 2010 International Mechanical Engineering Congress and Exposition (pp. 709-718). American Society of Mechanical Engineers. [3] Ogata, S., Kimura, A., & Watanabe, K. (2006). Effect of surfactant additives on centrifugal pump performance. Journal of Fluids Engineering, 128(4), 794-798. [4] Sellin, R. H. J., Hoyt, J. W., & Scrivener, O. (1982). The effect of drag-reducing additives on fluid flows and their industrial applications part 1: basic aspects. Journal of Hydraulic Research, 20(1), 29-68.
[5] Thomas, A., Gaillard, N., & Favero, C. (2012). Some key features to consider when studying acrylamide-based polymers for chemical enhanced oil recovery. Oil & Gas Science and Technology–Revue d’IFP Energies nouvelles, 67(6), 887-902.
[6] Barvenik, F. W. (1994). Polyacrylamide characteristics related to soil applications. Soil Science, 158(4), 235-243.
[7] Smook, G. A. (2002). Handbook for pulp & and paper technologists. Angus Wilde Publ., 218-221.
[8] Yang, S. Q. (2009). Drag reduction in turbulent flow with polymer additives. Journal of Fluids Engineering, 131(5), 051301.
[9] Benzi, R. (2010). A short review on drag reduction by polymers in wall bounded turbulence. Physica D: Nonlinear Phenomena, 239(14), 1338-1345.
[10] Housiadas, K. D., & Beris, A. N. (2013). On the skin friction coefficient in viscoelastic wall-bounded flows. International Journal of Heat and Fluid Flow, 42, 49-67.
[11] Zhang, X., Liu, L., Cheng, L., Guo, Q., & Zhang, N. (2013). Experimental study on heat transfer and pressure drop characteristics of air–water two-phase flow with the effect of polyacrylamide additive in a horizontal circular tube. International Journal of Heat and Mass Transfer, 58(1), 427-440.
[12] Thomas, A., Gaillard, N., & Favero, C. (2012). Some key features to consider when studying acrylamide-based polymers for chemical enhanced oil recovery. Oil & Gas Science and Technology–Revue d’IFP Energies nouvelles, 67(6), 887-902.
[13] Bjorneberg, D. L. (1998). Temperature, concentration, and pumping effects on PAM viscosity. Transactions of the ASAE, 41(6), 1651-1655.
[14] ASME V&V 20, Standard for Verification and Validation in Computational Fluid Dynamics and Heat Transfer, 2009. | ||
|
آمار تعداد مشاهده مقاله: 460 تعداد دریافت فایل اصل مقاله: 474 |
||
