سامانه پشتیبانی خدمات اطلاعات

  اخبار و اعلانات

 آمار

تعداد نشریات161
تعداد شماره‌ها6,468
تعداد مقالات69,896
تعداد مشاهده مقاله122,406,907
تعداد دریافت فایل اصل مقاله95,654,180
Morady, Shiva, Talafi Noghani, Mohammad, Saghafi Yazdi, Morteza. (1397). Effect of processing parameters on the mechano-chemical synthesis of nano crystalline Mo-Cu/Al2O3 composite. , 51(1), 13-19. doi: 10.22059/jufgnsm.2018.01.02
Shiva Morady; Mohammad Talafi Noghani; Morteza Saghafi Yazdi. "Effect of processing parameters on the mechano-chemical synthesis of nano crystalline Mo-Cu/Al2O3 composite". , 51, 1, 1397, 13-19. doi: 10.22059/jufgnsm.2018.01.02
Morady, Shiva, Talafi Noghani, Mohammad, Saghafi Yazdi, Morteza. (1397). 'Effect of processing parameters on the mechano-chemical synthesis of nano crystalline Mo-Cu/Al2O3 composite', , 51(1), pp. 13-19. doi: 10.22059/jufgnsm.2018.01.02
Morady, Shiva, Talafi Noghani, Mohammad, Saghafi Yazdi, Morteza. Effect of processing parameters on the mechano-chemical synthesis of nano crystalline Mo-Cu/Al2O3 composite. , 1397; 51(1): 13-19. doi: 10.22059/jufgnsm.2018.01.02

Effect of processing parameters on the mechano-chemical synthesis of nano crystalline Mo-Cu/Al2O3 composite

Journal of Ultrafine Grained and Nanostructured Materials
مقاله 1، دوره 51، شماره 1، شهریور 2018، صفحه 13-19    اصل مقاله (810.22 K)
نوع مقاله: Research Paper
شناسه دیجیتال (DOI): 10.22059/jufgnsm.2018.01.02
نویسندگان
Shiva Morady؛ Mohammad Talafi Noghani؛ Morteza Saghafi Yazdi*
Department of Materials Science and Engineering, Faculty of Engineering, Imam Khomeini International University, Qazvin, Iran
چکیده
In this study, molybdenum-copper/alumina nano composite was synthesized with mechano-chemical method using high energy planetary ball milling. The molybdenum oxide, copper oxide and aluminum powder were used as starting materials and reaction appeared to occur through a rapid combustion reaction process. The evaluation of powder particles after different milling times was studied by X-ray diffraction (XRD), differential thermal analysis/thermogravimetric (DTA/TG) and scanning electron microscopy (SEM). XRD results show that with increasing milling time at ambient temperature the peak intensities of powders decreases and significant peak broadening due to decrease in the size of crystallites observed. As a result, after 100 h milling time a molybdenum-copper/alumina metal matrix nanocomposite was formed which matrix had a crystallite size of about 42  nm for cu, calculated from Williamson-Hall equation. In fact by increasing the milling time after reduction of metal oxides, molybdenum dissolves in copper matrix and supersaturated Cu(Mo) solid solution with a homogenous distribution of nano-sized Al2O3 as reinforcement materials was formed. The thermal analysis curves of 10 minutes milled sample shows some peaks related to reduction of copper and molybdenum oxide with aluminum. In addition the small endothermic peak at 650 °C observed from DTA curve is due to the melting of remaining Al.
کلیدواژه‌ها
Ball milling؛ Mo-Cu/Al2O3؛ Nano-composite
مراجع

1. Heidarpour A, Karimzadeh F, Enayati MH. In situ synthesis mechanism of Al2O3–Mo nanocomposite by ball milling process. Journal of Alloys and Compounds. 2009;477(1-2):692-5.

2. Nawa M, Sekino T, Niihara K. Fabrication and mechanical behaviour of Al2O3/Mo nanocomposites. Journal of Materials Science. 1994;29(12):3185-92.

3. Martínez VdP, Aguilar C, Marín J, Ordoñez S, Castro F. Mechanical alloying of Cu–Mo powder mixtures and thermodynamic study of solubility. Materials Letters. 2007;61(4-5):929-33.

4. Sabooni S, Mousavi T, Karimzadeh F. Mechanochemical assisted synthesis of Cu(Mo)/Al2O3 nanocomposite. Journal of Alloys and Compounds. 2010;497(1-2):95-9.

5. Aguilar C, Ordóñez S, Marín J, Castro F, Martínez V. Study and methods of analysis of mechanically alloyed Cu–Mo powders. Materials Science and Engineering: A. 2007;464(1-2):288-94.

6. Sabooni S, Mousavi T, Karimzadeh F. Thermodynamic analysis and characterisation of nanostructured Cu(Mo) compounds prepared by mechanical alloying and subsequent sintering. Powder Metallurgy. 2012;55(3):222-7.

7. Dolatmoradi A, Raygan S, Abdizadeh H. Mechanochemical synthesis of W–Cu nanocomposites via in-situ co-reduction of the oxides. Powder Technology. 2013;233:208-14.

8. Ying DY, Zhang DL. Processing of Cu–Al2O3 metal matrix nanocomposite materials by using high energy ball milling. Materials Science and Engineering: A. 2000;286(1):152-6.

9. Aboraia MS, Abdalla GA, and Wasly HS. Synthesis and characterization of Al–Al2O3 and Al/(Al2O3-ZrO2) nanocomposites using high-energy milling. Int. Journal of Engineering Research and Applications. 2013;3:2248-9622.

10. Sheibani S, Khakbiz M, Omidi M. In situ preparation of Cu–MnO nanocomposite powder through mechanochemical synthesis. Journal of Alloys and Compounds. 2009;477(1-2):683-7.

11. Venugopal T, Rao KP, Murty BS. Synthesis of copper–alumina nanocomposite by reactive milling. Materials Science and Engineering: A. 2005;393(1-2):382-6.

12. Introduction to the Thermodynamics of Materials, Fifth Edition. CRC Press; 2008.

13. Suryanarayana C. Mechanical alloying and milling. Progress in Materials Science. 2001;46(1-2):1-184.

14. Matteazzi P, Caer GL. Synthesis of Nanocrystalline Alumina-Metal Composites by Room-Temperature Ball-Milling of Metal Oxides and Aluminum. Journal of the American Ceramic Society. 1992;75(10):2749-55.

آمار
تعداد مشاهده مقاله: 1,206
تعداد دریافت فایل اصل مقاله: 615


سامانه مدیریت نشریات علمی. قدرت گرفته از سیناوب