پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 161 |
| تعداد شمارهها | 6,489 |
| تعداد مقالات | 70,096 |
| تعداد مشاهده مقاله | 123,166,768 |
| تعداد دریافت فایل اصل مقاله | 96,397,874 |
Analysis of the Modifying Effect of Styrene Butadiene Rubber Latex Copolymer on Strength and Permeability Properties of Structural Light Aggregate Concrete | ||
| Civil Engineering Infrastructures Journal | ||
| مقاله 9، دوره 52، شماره 1، شهریور 2019، صفحه 137-154 اصل مقاله (976.43 K) | ||
| نوع مقاله: Research Papers | ||
| شناسه دیجیتال (DOI): 10.22059/ceij.2019.255225.1476 | ||
| نویسندگان | ||
| Sajad Rezaei* ؛ Keyvan Abedzadeh | ||
| Faculty of Civil Engineering, Pooyesh Institute of Higher Education, Qom, Iran. | ||
| چکیده | ||
| Polymers not only possess repairing functions concerning the concrete structures, but also due to their properties are used in making different types of polymer cements and improving the matrix structure of cement materials, enhancing the viscosity, mechanical, and stability power of concretes. Today, there is limited knowledge on the use of SBR in structural light aggregate concrete. In the present research, light expanded clay aggregate was used to produce light weight concrete weighing 1740 to 1780 kg/M3. Unlike the previously conducted studies in which the desirable properties of concrete were achieved by increasing the compressive strength, in the current study we have used C25 light concrete without any cement supplements. SBR latex copolymer was incorporated in concrete directly (additive) and indirectly (light aggregates coating) each based on a combinational performance of 28 and 60 days. The results revealed that based on the used cement matrix, the optimal performance of the latex in the direct method was enhanced by increasing the bending and tensile strength rather than the compressive strength. The indirect presence of latex not only imposed a new limit in ITZ, but also had no interfering role in modifying the chemical mechanism of cement hydration. Thus, the behavior of this concrete did not show any enhancement in the mechanical properties as it did in the case of direct implication of latex. The study also showed that the presence of latex in both methods led to reduced permeability of the concrete. This research also looked into the impact of cement matrix capability, latex consumption rate, curing age and method and the effect of copolymer ratio on improving the light weight concrete stability and mechanical properties. | ||
| کلیدواژهها | ||
| Combinational Curing؛ Mechanical Strength؛ Permeability؛ SBR Latex Copolymer؛ Structural Lightweight Aggregate Concrete | ||
| مراجع | ||
|
ACI Committee 548.1. (2009). Guide for the use of polymers in concrete, American Concrete Institute, Detroit.
ACI Committee 211.2. (2004). Standard practice for selecting proportion for structural lightweight concrete, American Concrete Institute, Detroit.
Ardakani, A. and Yazdani, M. (2014). “The relation between particle density and static elastic moduli of lightweight expanded clay aggregates”, Applied Clay Science, 93, 28-34.
Assaad, J.J. (2018). “Development and use of polymer-modified cement for adhesive and repair applications”, Construction and Building Materials, 163, 139-148.
Assaad, J. and Daou, Y. (2017). “Behavior of structural polymer-modified concrete containing recycled aggregates”, Journal of Adhesion Science and Technology, 31(8), 874-896.
Assaad, J.J. and Issa, C.A. (2017). “Mixture optimisation of polymer-modified lightweight SCC”, Magazine of Concrete Research, 69(14), 745-756.
Bogas, J.A., Nogueira, R. and Almeida, N.G. (2014). “Influence of mineral additions and different compositional parameters on the shrinkage of structural expanded clay lightweight concrete”, Materials and Design, (1980-2015), 56, 1039-1048.
Bogas, J.A., Gomes, M.G. and Real, S. (2015a). “Capillary absorption of structural lightweight aggregate concrete”, Materials and Structures, 48(9), 2869-2883.
Bogas, J.A., de Brito, J. and Figueiredo, J.M. (2015b). “Mechanical characterization of concrete produced with recycled lightweight expanded clay aggregate concrete”, Journal of Cleaner Production, 89, 187-195.
Doğan, M. and Bideci, A. (2016). “Effect of Styrene Butadiene Copolymer (SBR) admixture on high strength concrete”, Construction and Building Materials, 112, 378-385.
Eren, F., Gödek, E., Keskinateş, M., Tosun-Felekoğlu, K. and Felekoğlu, B. (2017). “Effects of latex modification on fresh state consistency, short term strength and long term transport properties of cement mortars”, Construction and Building Materials, 133, 226-233.
Ferrara, L., Cortesi, L. and Ligabue, O. (2015). “Internal curing of concrete with presaturated LWA: A preliminary investigation”, Special Publication, 305, 12-1.
Issa, C. A. and Assaad, J.J. (2017). “Stability and bond properties of polymer-modified self-consolidating concrete for repair applications”, Materials and Structures, 50(1), 28.
Lewis, W.J. and Lewis, G. (1990). “The influence of polymer latex modifiers on the properties of concrete”, Composites, 21(6), 487-494.
Martínez-García, C., González-Fonteboa, B., Martínez-Abella, F. and Carro-López, D. (2017). “Performance of mussel shell as aggregate in plain concrete”, Construction and Building Materials, 139, 570-583.
Miller, N.M. and Tehrani, F.M. (2017). “Mechanical properties of rubberized lightweight aggregate concrete”, Construction and Building Materials, 147, 264-271.
Mindess, S., Young, J.F. and Darwin, D. (1981). Concrete, Prentice-Hall. Englewood Cliffs, NJ, 481 P.
Mo, K.H., Alengaram, U.J., Visintin, P., Goh, S.H. and Jumaat, M.Z. (2015). “Influence of lightweight aggregate on the bond properties of concrete with various strength grades”, Construction and Building Materials, 84, 377-386.
Mo, K.H., Alengaram, U.J. and Jumaat, M.Z. (2016). “Bond properties of lightweight concrete, A review”, Construction and Building Materials, 112, 478-496.
Mo, K.H., Goh, S.H., Alengaram, U.J., Visintin, P. and Jumaat, M.Z. (2017a). “Mechanical, toughness, bond and durability-related properties of lightweight concrete reinforced with steel fibres”, Materials and Structures, 50(1), 46.
Mo, K.H., Ling, T.C., Alengaram, U.J., Yap, S.P. and Yuen, C.W. (2017b). “Overview of supplementary cementitious materials usage in lightweight aggregate concrete”, Construction and Building Materials, 139, 403-418.
Muhammad, N.Z., Keyvanfar, A., Majid, M.Z.A., Shafaghat, A. and Mirza, J. (2015). “Waterproof performance of concrete: A critical review on implemented approaches”, Construction and Building Materials, 101, 80-90.
Nair, H., Ozyildirim, C. and Sprinkel, M. (2016). “Use of lightweight concrete for reducing cracks in bridge decks (No. FHWA/VTRC 16-R14)”, Virginia Transportation Research Council.
Nováková, I. and Mikulica, K. (2016). “Properties of concrete with partial replacement of natural aggregate by recycled concrete aggregates from precast production”, Procedia Engineering, 151, 360-367.
Ohama, Y. (1995). Handbook of polymer-modified concrete and mortars: Properties and process technology, William Andrew.
Pascal, S., Alliche, A. and Pilvin, P. (2004). “Mechanical behaviour of polymer modified mortars”, Materials Science and Engineering: A, 380(1-2), 1-8.
Ramli, M. and Tabassi, A.A. (2012). “Effects of polymer modification on the permeability of cement mortars under different curing conditions: A correlational study that includes pore distributions, water absorption and compressive strength”, Construction and Building Materials, 28(1), 561-570.
Ramli, M., Tabassi, A.A. and Hoe, K.W. (2013). “Porosity, pore structure and water absorption of polymer-modified mortars: An experimental study under different curing conditions”, Composites Part B: Engineering, 55, 221-233.
Real, S. and Bogas, J.A. (2017). “Oxygen permeability of structural lightweight aggregate concrete”, Construction and Building Materials, 137, 21-34.
Said, A.M., Quiroz, O.I., Hatchett, D.W. and ElGawady, M. (2016). “Latex-modified concrete overlays using waste paint”, Construction and Building Materials, 123, 191-197.
Chandra Berntsson, L. (2003). Lightweight aggregate concrete science, technology and applications.
Sayadi, A.A., Tapia, J.V., Neitzert, T. R. and Clifton, G.C. (2016). “Effects of expanded polystyrene (EPS) particles on fire resistance, thermal conductivity and compressive strength of foamed concrete”, Construction and Building Materials, 112, 716-724.
Shafigh, P., Ghafari, H., Mahmud, H.B. and Jumaat, M.Z. (2014). “A comparison study of the mechanical properties and drying shrinkage of oil palm shell and expanded clay lightweight aggregate concretes”, Materials and Design, 60, 320-327.
Shafigh, P., Jumaat, M.Z., Mahmud, H.B. and Alengaram, U.J. (2013). “Oil palm shell lightweight concrete containing high volume ground granulated blast furnace slag”, Construction and Building Materials, 40, 231-238.
Silva, D.A. and Monteiro, P.J. (2006). “The influence of polymers on the hydration of Portland cement phases analyzed by soft X-ray transmission microscopy”, Cement and Concrete Research, 36(8), 1501-1507.
Valcuende, M. and Parra, C. (2009). “Bond behaviour of reinforcement in self-compacting concretes”, Construction and Building Materials, 23(1), 162-170.
Vargas, P., Restrepo-Baena, O. and Tobón, J.I. (2017). “Microstructural analysis of Interfacial Transition Zone (ITZ) and its impact on the compressive strength of lightweight concretes”, Construction and Building Materials, 137, 381-389.
Wang, M., Wang, R., Yao, H., Farhan, S., Zheng, S., Wang, Z. and Jiang, H. (2016). “Research on the mechanism of polymer latex modified cement”, Construction and Building Materials, 111, 710-718.
Wang, R., Wang, P.M. and Li, X.G. (2005). “Physical and mechanical properties of styrene-butadiene rubber emulsion modified cement mortars”, Cement and Concrete Research, 35(5), 900-906.
Zhang, P., Xie, N., Cheng, X., Feng, L., Hou, P. and Wu, Y. (2018). “Low dosage nano-silica modification on lightweight aggregate concrete”, Nanomaterials and Nanotechnology, 8, 1847980418761283. | ||
|
آمار تعداد مشاهده مقاله: 723 تعداد دریافت فایل اصل مقاله: 549 |
||