پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 162 |
| تعداد شمارهها | 6,578 |
| تعداد مقالات | 71,078 |
| تعداد مشاهده مقاله | 125,709,561 |
| تعداد دریافت فایل اصل مقاله | 98,942,865 |
Optimization of thermal curing cycle for a large epoxy model | ||
| Journal of Computational Applied Mechanics | ||
| مقاله 9، دوره 50، شماره 2، اسفند 2019، صفحه 282-288 اصل مقاله (876.95 K) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22059/jcamech.2019.73015 | ||
| نویسندگان | ||
| Mahmood Yaghoubi* ؛ Zafar Namazian | ||
| school of mechanical engineering, Shiraz university, Shiraz, Iran | ||
| چکیده | ||
| Heat generation in an exothermic reaction during the curing process and low thermal conductivity of the epoxy resin produces high peak temperature and temperature gradients which result in internal and residual stresses, especially in large epoxy samples. In this paper, an optimization algorithm was developed and applied to predict the thermal cure cycle to minimize the temperature peak and thermal gradients within the material of an industrial epoxy model during the curing process. An inverse analysis was used to obtain the new coefficients of Kamal’s equations for the model. To validate and verify the developed model, temperature profiles for several points of the material in the model were obtained by numerical simulation and compared with the previously experimentally measured data. With validated curing simulation, the mentioned inverse analysis and optimization algorithm were utilized to find the thermal curing cycle with several isothermal holds and temperature ramps. The new objective reference was proposed for the first time and used to optimize the cure cycle, which subsequently produced the same temperature profiles for all points. The results showed that the obtained optimized thermal curing cycle was most effective to decrease the peak temperature as well as temperature gradients of the material. | ||
| کلیدواژهها | ||
| Cure cycle optimization؛ Inverse analysis؛ Temperature gradients؛ Large epoxy model؛ Peak temperature | ||
| مراجع | ||
|
[1] C. G. Zelibe, O. Adewumi, A. Onitiri, 2019, Numerical investigation of the performance of fibre-glass/talc filled epoxy composite as insulator in heating applications, Journal of Computational Applied Mechanics: -.
[2] I. Jones, Y. Zhou, S. Jeelani, J. Mabry, 2008, Effect of polyhedral-oligomeric-sil-sesquioxanes on thermal and mechanical behavior of SC-15 epoxy, Express Polymer Letters 2 (7): 494-501.
[3] P. Ghabezi, M. Farahani, 2016, Composite adhesive-bonded joint reinforcement by incorporation of nano-alumina particles, J Comput Appl Mech 47 (2): 231-239.
[4] J. Duan, C. Kim, P. Jiang, 2009, On-line monitoring of cycloaliphatic epoxy/acrylate interpenetrating polymer networks formation and characterization of their mechanical properties, Journal of polymer research 16 (1): 45-54.
[5] Y. A. Chekanov, V. Korotkov, B. Rozenberg, E. Dhzavadyan, L. Bogdanova, 1995, Cure shrinkage defects in epoxy resins, Polymer 36 (10): 2013-2017.
[6] M. Ghassemieh, M. Rezapour, A. Taghinia, 2017, Predicting Low Cycle Fatigue Life through Simulation of Crack in Cover Plate Welded Beam to Column Connections, Journal of Computational Applied Mechanics 48 (1): 39-52.
[7] P. Wang, H. Lei, X. Zhu, H. Chen, D. Fang, 2018, Investigation on the mechanical properties of epoxy resin with void defects using digital image correlation and image-based finite element method, Polymer Testing 72: 223-231.
[8] Y. He, Q. Chen, S. Yang, C. Lu, M. Feng, Y. Jiang, G. Cao, J. Zhang, C. Liu, 2018, Micro-crack behavior of carbon fiber reinforced Fe3O4/graphene oxide modified epoxy composites for cryogenic application, Composites Part A: Applied Science and Manufacturing 108: 12-22.
[9] C. Leistner, S. Hartmann, J. Wittrock, K. Bode, 2018, Shrinkage behavior of Araldite epoxy resin using Archimedes' principle, Polymer testing 67: 409-416.
[10] J. Zhang, 2009, Effect of cure cycle on curing process and hardness for epoxy resin, eXPRESS Polymer Letters 3 (9): 534-541.
[11] S. Pusatcioglu, J. Hassler, A. Fricke, H. McGee Jr, 1980, Effect of temperature gradients on cure and stress gradients in thick thermoset castings, Journal of Applied Polymer Science 25 (3): 381-393.
[12] M. Hojjati, S. Hoa, 1994, Curing simulation of thick thermosetting composites, Composites Manufacturing 5 (3): 159-169.
[13] A. K. Kulshreshtha, C. Vasile, 2002, Neuroclave: The Intelligent Autoclave, Handbook of Polymer Blends and Composites, Shrewsbury, Rapra Technology
[14] C. Warnock, T. T. Briggs, Cure Cycle Development and Qualification for Thick-Section Composites, United States, pp. 2016.
[15] R. Sekula, P. Saj, T. Nowak, K. Kaczmarek, K. Forsman, A. Rautiainen, J. Grindling, 2003, 3‐D modeling reactive molding processes: From tool development to industrial applicatio, Advances in Polymer Technology 22 (1): 1–14.
[16] K. Kasza, L. Matysiak, L. Malinowski, 2010, Method to describe curing in large epoxy samples, Advances in Polymer Technology 28 (4): 267–275.
[17] E. Ruiz, F. Trochu, 2005, Numerical analysis of cure temperature and internal stresses in thin and thick RTM parts, Composites Part A: Applied Science and Manufacturing 36 (6): 806-826.
[18] Ł. Matysiak, 2014, Experimental analysis and inverse approach in numerical modelling of curing process of composite materials, Thesis, Institute of Thermal Technology, Faculty of Energy and Environmental Engineering, Silesian University of Technology.
[19] M. N. Ozisik, H. R. B. Orlande, 2000, Inverse Heat Transfer. Fundamentals And Applications, Taylor & Francis, New York | ||
|
آمار تعداد مشاهده مقاله: 553 تعداد دریافت فایل اصل مقاله: 468 |
||
سامانه مدیریت نشریات علمی. قدرت گرفته از سیناوب