پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 161 |
| تعداد شمارهها | 6,532 |
| تعداد مقالات | 70,501 |
| تعداد مشاهده مقاله | 124,099,270 |
| تعداد دریافت فایل اصل مقاله | 97,206,808 |
Production of Eco-Friendly Geopolymer Concrete by using Waste Wood Ash for a Sustainable Environment | ||
| Pollution | ||
| دوره 7، شماره 4، دی 2021، صفحه 993-1006 اصل مقاله (1.3 M) | ||
| نوع مقاله: Original Research Paper | ||
| شناسه دیجیتال (DOI): 10.22059/poll.2021.320857.1039 | ||
| نویسندگان | ||
| Kadarkarai Arunkumar* 1؛ Muthiah Muthukannan1؛ Arunachalam Suresh Kumar1؛ Arunasankar Chithambar Ganesh2؛ Rangaswamy Kanniga Devi3 | ||
| 1School of Environmental and Construction Technology, Kalasalingam Academy of Research and Education, Krishnan kovil, Tamil Nadu, India | ||
| 2Department of Civil Engineering, Sree Vidya Nikethan Engineering College, Tripati, India | ||
| 3School of Computer Science and Engineering, Kalasalingam Academy of Research and Education, Krishnan kovil, Tamil Nadu, India | ||
| چکیده | ||
| Climate change could be exacerbated by waste disposal problems, which destroy the ecosystem. Utilizing waste byproducts in creating eco-friendlier geopolymer concrete was hypothesised to be suitable and sustainable to overcome the negative impacts of wastes. The researchers had missed out on developing an alternate binder due to increasing demand for fly ash, high alkaline activators, and higher curing temperatures. This research used waste wood ash that is readily accessible in local restaurants and has an inherent potassium constituent. It has decided to replace the fly ash with waste wood ash obtained through nearby restaurants at intervals of 10 percent. The fresh and mechanical features have been discovered over long curing periods to assess the impact of waste wood ash. SEM and XRD have been used for characterising the microstructure of selected geopolymer mixes. In terms of setting properties and all mechanical parameters, replacing 30 percent waste wood ash produced enhanced results. The optimised mix could be used in geopolymer to replace fly ash and reduce the cost of alkaline activators while also reducing ecosystem damage. | ||
| کلیدواژهها | ||
| Wood waste ash؛ Low calcium؛ Eco-friendly geopolymer concrete؛ SEM؛ XRD | ||
| مراجع | ||
|
Abdulkareem, O. A., Ramli, M. and Matthews, J. C, (2019). Production of geopolymer mortar system containing high calcium biomass wood ash as a partial substitution to fly ash: An early age evaluation. Compos. Part B Eng., 174; 106941.
Amran, Y. H. M., Alyousef, R., Alabduljabbar, H. and El-Zeadani, M. (2020). Clean production and properties of geopolymer concrete; A review. J. Clean. Prod. 251; 119679.
Anuradha, R., (2011). Modified Guidelines for Geopolymer Concrete Mix Design using Indian Standard. Asian J. Civ. Eng. (Building Housing), 13 (3); 357–368.
Arunachalam, S.K., Muthiah, M., Rangaswamy, K. D. Kadarkarai, A. and Arunasankar, C. G, (2021). Improving the structural performance of reinforced geopolymer concrete incorporated with hazardous heavy metal waste ash. World J. Eng., ahead-of-print.
Arunkumar, K. Muthukannan, M. Suresh kumar, A. and Chithambar Ganesh, A. (2021). Mitigation of waste rubber tire and waste wood ash by the production of rubberized low calcium waste wood ash based geopolymer concrete and influence of waste rubber fibre in setting properties and mechanical behavior. Environ. Res., 194; 110661.
Arunkumar, K. Muthukannan, M. Dinesh Babu, A. Hariharan, A. L, and Muthuramalingam, T. (2020). Effect on addition of Polypropylene fibers in wood ash-fly ash based geopolymer concrete. IOP Conf. Ser. Mater. Sci. Eng., 872; 012162.
Arunkumar, K., Muthukannan, M., Kumar, A.S., Ganesh, A.C. and Devi, R.K., (2021). Cleaner Environment Approach by the Utilization of Low Calcium Wood Ash in Geopolymer Concrete. Appl. Sci. Eng. Prog., 1–13.
Arunkumar, K. Muthukannan, M. Suresh Kumar, A. Chithambar Ganesh, A. and Kanniga Devi, R. (2021). Invention of sustainable geopolymer concrete made with low calcium waste wood ash. World J. Eng.,. ahead-of-print.
Assi, L.N, Carter, K, Deaver, E. and Ziehl, P. (2020). Review of availability of source materials for geopolymer/sustainable concrete. J. Clean. Prod., 263; 121477.
ASTM-C293, (2015). C293 - 15 Flexural Strength of Concrete (Using Simple Beam With Center-Point Loading). ASTM Int., 1–3.
ASTM C109/C109M-02., (2002). Standard Test Method for Compressive Strength of Hydraulic Cement Mortars. Annu. B. ASTM Stand., 04 1–6.
ASTM C215, (1991). Standard Test Method for Fundamental Transverse, Longitudinal, and Torsional Resonant Frequencies of Concrete Specimens, C 215. Annu. B. ASTM Stand. Am. Soc. Test. Mater., 1–7.
ASTM C618, (2010). Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use. Annu. B. ASTM Stand., (C); 3–6.
Ban, C. C, and Ramli, M. (2012). Characterisation of high calcium wood ash for use as a constituent in wood ash-silica fume ternary blended cement. Adv. Mater. Res., 346 3–11.
Ban, C. C., Ken, P. W, and Ramli, M. (2017). Mechanical and Durability Performance of Novel Self-activating Geopolymer Mortars. Procedia Eng., 171; 564–571.
British Standard, (1999). BS EN 196-3:1995 - Methods of testing cement - Part 3: Determination of setting time and soundness. Br. Stand. Inst.
Cheah, C. B, and Ramli, M. (2011). The implementation of wood waste ash as a partial cement replacement material in the production of structural grade concrete and mortar: An overview. Resour. Conserv. Recycl., 55 (7); 669–685.
Cheah, C. B, and Ramli, M. (2012). Load capacity and crack development characteristics of HCWA-DSF high strength mortar ferrocement panels in flexure. Constr. Build. Mater., 36; 348–357.
Cheah, C. B, and Ramli, M. (2013). The structural behaviour of HCWA ferrocement-reinforced concrete composite slabs. Compos. Part B Eng., 51; 68–78.
Cheah, C. B., Part, W. K, and Ramli, M. (2015). The hybridizations of coal fly ash and wood ash for the fabrication of low alkalinity geopolymer load bearing block cured at ambient temperature. Constr. Build. Mater., 88; 41–55.
Cheah, C. B., Samsudin, M. H, Ramli, M. Part, W. K, and Tan, L. E, (2017). The use of high calcium wood ash in the preparation of Ground Granulated Blast Furnace Slag and Pulverized Fly Ash geopolymers: A complete microstructural and mechanical characterization. J. Clean. Prod., 156; 114–123.
Chithambar, G. A. and Muthukannan, M. (2019). Investigation on the glass fiber reinforced geopolymer concrete made of M-sand. J. Mater. Eng. Struct., 6 (4); 501–512.
Chithambar Ganesh, A. and Muthukannan, M. (2018). A review of recent developments in geopolymer concrete. Int. J. Eng. Technol., 7 (5); 696.
Chithambar Ganesh, A. and Muthukannan, M. (2019). Experimental Study on the Behaviour of Hybrid Fiber Reinforced Geopolymer Concrete under Ambient Curing Condition. IOP Conf. Ser. Mater. Sci. Eng., 561; 012014.
Chithambar Ganesh, A., Muthukannan, M., Malathy, R. and Ramesh Babu, C. (2019). An Experimental Study on Effects of Bacterial Strain Combination in Fibre Concrete and Self-Healing Efficiency. KSCE J. Civ. Eng., 23 (10); 4368–4377.
Chithambar Ganesh, A., Muthukannan, M., Dhivya, M., Sangeetha, C.B. and Daffodile, S.P. (2020). Structural performance of hybrid fiber geopolymer concrete beams. IOP Conf. Ser. Mater. Sci. Eng., 872; 012155.
Ganesh, A.C. and Muthukannan, M. (2021). Development of high performance sustainable optimized fiber reinforced geopolymer concrete and prediction of compressive strength. J. Clean. Prod., 282; 124543.
Ganesh, C., Sivasubramanaian, J., Seshamahalingam, M.S., Millar, J. and Kumar, V.J. (2021). Investigation on the Performance of Hybrid Fiber Reinforced Geopolymer Concrete Made of M-Sand under Heat Curing. Mater. Sci. Forum, 1019; 73–81.
Ganesh, C., Muthukannan, M., Suresh Kumar, A. and Arunkumar, K. (2021). Influence of Bacterial Strain Combination in Hybrid Fiber Reinforced Geopolymer Concrete subjected to Heavy and Very Heavy Traffic Condition. J. Adv. Concr. Technol., 19 (4); 359–369.
Hajimohammadi, A., Ngo, T. and Vongsvivut, J. (2019). Interfacial chemistry of a fly ash geopolymer and aggregates. J. Clean. Prod., 231; 980–989.
Hamidi, R.M., Man, Z. and Azizli, K.A. (2016). Concentration of NaOH and the Effect on the Properties of Fly Ash Based Geopolymer. Procedia Eng., 148; 189–193.
Huntzinger, D.N. and Eatmon, T.D. (2009). A life-cycle assessment of Portland cement manufacturing: comparing the traditional process with alternative technologies. J. Clean. Prod., 17 (7); 668–675.
Huseien, G.F., Ismail, M., Khalid, N.H.A., Hussin, M.W. and Mirza, J. (2018). Compressive strength and microstructure of assorted wastes incorporated geopolymer mortars: Effect of solution molarity. Alexandria Eng. J., 57 (4); 3375–3386.
Hwang, C.-L., Huynh, T.-P. (2015). Effect of alkali-activator and rice husk ash content on strength development of fly ash and residual rice husk ash-based geopolymers. Constr. Build. Mater., 101 (9); 1–9.
Jiang, X., Zhang, Y., Xiao, R., Polaczyk, P., Zhang, M., Hu, W., Bai, Y. and Huang, B. (2020). A comparative study on geopolymers synthesized by different classes of fly ash after exposure to elevated temperatures. J. Clean. Prod., 270; 122500.
Kabir, S. M. A., Alengaram, U. J., Jumaat, M. Z., Yusoff, S., Sharmin, A. and Bashar, I. I. (2017). Performance evaluation and some durability characteristics of environmental friendly palm oil clinker based geopolymer concrete. J. Clean. Prod., 161; 477–492.
Kaewmee, P., Song, M., Iwanami, M., Tsutsumi, H. and Takahashi, F. (2020). Porous and reusable potassium-activated geopolymer adsorbent with high compressive strength fabricated from coal fly ash wastes. J. Clean. Prod., 272; 122617.
Liang, G., Zhu, H., Zhang, Z., Wu, Q. and Du, J. (2019). Investigation of the waterproof property of alkali-activated metakaolin geopolymer added with rice husk ash. J. Clean. Prod., 230; 603–612.
Malkawi, A.B., Nuruddin, M.F., Fauzi, A., Almattarneh, H. and Mohammed, B.S. (2016). Effects of Alkaline Solution on Properties of the HCFA Geopolymer Mortars. Procedia Eng., 148; 710–717.
Mehta, A. and Siddique, R. (2018). Sustainable geopolymer concrete using ground granulated blast furnace slag and rice husk ash: Strength and permeability properties. J. Clean. Prod., 205; 49–57.
Nuaklong, P., Jongvivatsakul, P., Pothisiri, T., Sata, V. and Chindaprasirt, P. (2020). Influence of rice husk ash on mechanical properties and fire resistance of recycled aggregate high-calcium fly ash geopolymer concrete. J. Clean. Prod., 252; 119797.
Pavithra, P., Srinivasula Reddy, M., Dinakar, P., Hanumantha Rao, B., Satpathy, B.K. and Mohanty, A.N. (2016). A mix design procedure for geopolymer concrete with fly ash. J. Clean. Prod., 133; 117–125.
Rajamane N. P. and Jeyalakshmi R. (2014). Quantities of Sodium Hydroxide Solids and Water to Prepare Sodium Hydroxide Solution of Given Molarity for Geopolymer Concrete Mixes MIXES. ICI Tech. Pap., 4–9.
Rangan, B. V. (2008). Fly Ash-Based Geopolymer Concrete (Column). Eng. Fac. Curtin Univ. Technol. Perth, Aust., 3124–3130.
Samsudin, M. H. and Ban, C. C. (2015). Optimization on the hybridization ratio of ground granulated blast furnace slag and high calcium wood ash (GGBS – HCWA) for the fabrication of geopolymer mortar. Adv. Environ. Biol., 9 (4); 22–25.
Shadnia, R. and Zhang, L. (2017). Experimental Study of Geopolymer Synthesized with Class F Fly Ash and Low-Calcium Slag. J. Mater. Civ. Eng., 29 (10); 04017195.
Sivasakthi, M., Jeyalakshmi, R. and Rajamane, N.P. (2021). Fly ash geopolymer mortar: Impact of the substitution of river sand by copper slag as a fine aggregate on its thermal resistance properties. J. Clean. Prod., 279; 123766.
Suresh Kumar, A., Muthukannan, M. and Sri Krishna, I. (2020). Optimisation of bio medical waste ash in GGBS based of geopolymer concrete. IOP Conf. Ser. Mater. Sci. Eng., 872; 012163.
Suresh Kumar, A., Muthukannan, M., Kanniga Devi, R., Arunkumar, K. and Chithambar Ganesh, A. (2021). Reduction of hazardous incinerated bio-medical waste ash and its environmental strain by utilizing in green concrete. Water Sci. Technol., (ahead of print).
Thakur, R.N. and Ghosh, S. (2009). Effect of mix composition on compressive strength and microstructure of fly ash based geopolymer composites. J. Eng. Appl. Sci., 4 (4); 68–74.
Wang, Y., Liu, X., Zhang, W., Li, Z., Zhang, Y., Li, Y. and Ren, Y. (2020). Effects of Si/Al ratio on the efflorescence and properties of fly ash based geopolymer. J. Clean. Prod., 244; 118852.
Winnefeld, F., Leemann, A., Lucuk, M., Svoboda, P. and Neuroth, M. (2010). Assessment of phase formation in alkali activated low and high calcium fly ashes in building materials. Constr. Build. Mater., 24 (6); 1086–1093.
Xiao, R., Ma, Y., Jiang, X., Zhang, M., Zhang, Y., Wang, Y., Huang, B. and He, Q. (2020). Strength, microstructure, efflorescence behavior and environmental impacts of waste glass geopolymers cured at ambient temperature. J. Clean. Prod., 252; 119610.
Yousefi Oderji, S., Chen, B., Ahmad, M.R. and Shah, S.F.A. (2019). Fresh and hardened properties of one-part fly ash-based geopolymer binders cured at room temperature: Effect of slag and alkali activators. J. Clean. Prod., 225; 1–10.
Zakka, W.P., Abdul Shukor Lim, N.H. and Chau Khun, M. (2021). A scientometric review of geopolymer concrete. J. Clean. Prod., 280; 124353.
Zhang, P., Gao, Z., Wang, J., Guo, J., Hu, S. and Ling, Y. (2020). Properties of fresh and hardened fly ash/slag based geopolymer concrete: A review. J. Clean. Prod., 270; 122389.
Zhang, P., Wang, K., Li, Q., Wang, J. and Ling, Y. (2020). Fabrication and engineering properties of concretes based on geopolymers/alkali-activated binders - A review. J. Clean. Prod., 258; 120896.
Zhang, P., Wang, K., Wang, J., Guo, J. and Ling, Y., (2021). Macroscopic and microscopic analyses on mechanical performance of metakaolin/fly ash based geopolymer mortar. J. Clean. Prod., 294; 126193. | ||
|
آمار تعداد مشاهده مقاله: 974 تعداد دریافت فایل اصل مقاله: 1,157 |
||