پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 161 |
| تعداد شمارهها | 6,533 |
| تعداد مقالات | 70,506 |
| تعداد مشاهده مقاله | 124,125,073 |
| تعداد دریافت فایل اصل مقاله | 97,233,607 |
Improving Cyclic Behavior of Steel Plate Shear Walls with Elliptical Perforations | ||
| Civil Engineering Infrastructures Journal | ||
| دوره 53، شماره 1، شهریور 2020، صفحه 89-102 اصل مقاله (1.73 M) | ||
| نوع مقاله: Research Papers | ||
| شناسه دیجیتال (DOI): 10.22059/ceij.2019.276064.1553 | ||
| نویسندگان | ||
| Ebrahim Zamani Beydokhti* 1؛ Hashem Khatibi2 | ||
| 1Department of civil engineering, Shahrood University of Technology | ||
| 2Parsrazavi Institute of Higher Education, Gonabad, Iran. | ||
| چکیده | ||
| In this paper, the effect of elliptical shape openings was numerically compared to the case when circular openings were used in the steel panel shear walls. At first, the finite element model in ABAQUS was calibrated by experimental results, obtained from previous studies. Then, three steel shear panels with different sizes of elliptical openings were analyzed under cyclic loads, and the results were compared to those circular perforations. Moreover, comparisons of cyclic response parameters such as elastic stiffness, ductility ratio, and energy absorption were made. According to the results, the shape of the openings has a significant effect on the seismic behavior of the perforated shear wall. The elliptical opening with the smaller to larger diameter ratio, equal to 0.5, increased the ultimate capacity by 15%. Furthermore, the elastic stiffness, ductility ratio of the frame, and the absorbed energy were promoted by 28%, 3%, and 8%, respectively. Finally, the distance between the openings was improved. Using a ratio of about 0.17 for the center to center distance of elliptical openings to the total width of steel panel led to the best performance. | ||
| کلیدواژهها | ||
| Circular Opening؛ Elliptical Opening؛ Finite Element Analysis؛ Perforated Shear Wall؛ Steel Panel | ||
| مراجع | ||
|
AISC 341. (2016). Seismic provision for structural steel buildings, Chicago, Illinois: American Institute of Steel Construction. AISC-97. (1997). Seismic provisions for structural steel buildings, Chicago, Illinois: American Institute of Steel Construction. CSA- S16-14. (2014). Design of steel structures, Canadian Standards Association, Toronto, Ontario, Canada Bahrebar, M., Kabir, M.Z., Zirakian, T., Hajsadeghi, M. and Lim, J.B. (2016). "Structural performance assessment of trapezoidally-corrugated and centrally-perforated steel plate shear walls", Journal of Constructional Steel Research, 122, 584-594. Berman, J.W. and Bruneau, M. (2005). 'Experimental investigation of light-gauge steel plate shear walls", Journal of Structural Engineering, 131, 259-267. Bhowmick, A.K., Grondin, G.Y. and Driver, R.G. (2014). "Nonlinear seismic analysis of perforated steel plate shear walls", Journal of Constructional Steel Research, 94, 103-113. Broujerdian, V., Shayanfar, M. and Ghamari, A. (2017). “Corner crack effect on the seismic behavior of steel plate shear wall system”, Civil Engineering Infrastructures Journal, 50(2), 311-332. Gholizadeh, S. and Shahrezaei, A.M. (2015). "Optimal placement of steel plate shear walls for steel frames by bat algorithm", The Structural Design of Tall and Special Buildings, 24, 1-18. He, L., Togo, T., Hayashi, K., Kurata, M. and Nakashima, M. (2016). "Cyclic behavior of multirow slit shear walls made from low-yield-point steel", Journal of Structural Engineering, 142, 04016094. Hibbitt, D., Karlsson, B. and Sorensen, E.P. (2009). ABAQUS/CAE Version 6.8, Standard user's manual, Rhode Island, USA. Lu, J., Yu, S., Xia, J., Qiao, X. and Tang, Y. (2018). "Experimental study on the hysteretic behavior of steel plate shear wall with unequal length slits", Journal of Constructional Steel Research, 147, 477-487. Nie, J. and Zhu, L. (2014). "Lateral stiffness of steel plate shear walls", Science China Technological Sciences, 57, 151-162. Office of Deputy for Strategic Supervision (ODSS). (2009). Commentary of instruction for seismic rehabilitation of existing buildings, No: 361, Iran. Roberts, T.M. and Sabouri-Ghomi, S. (1992). "Hysteretic characteristics of unstiffened perforated steel plate shear panels", Thin-Walled Structures, 14, 139-151. Shekastehband, B., Azaraxsh, A. and Showkati, H. (2017). "Experimental and numerical study on seismic behavior of LYS and HYS steel plate shear walls connected to frame beams only", Archives of Civil and Mechanical Engineering, 17, 154-168. Shekastehband, B. and Azaraxsh, A.A. (2019). "Strength, stiffness, ductility, and dissipated energy reduction of semisupported steel shear walls (SSSW) due to a circular opening", The Structural Design of Tall and Special Buildings, 28, e1558. TahamouliRoudsari, M., Torkaman, M., Entezari, A.R. and Rahimi, H. (2019), "Experimental investigation of strengthening reinforced concrete moment resisting frames using partially attached steel infill plate", Structures, 19, 173-183. Tsavdaridis, K.D. and D'Mello, C. (2012). "Optimisation of novel elliptically-based web opening shapes of perforated steel beams", Journal of Constructional Steel Research, 76, 39-53. Valizadeh, H., Sheidaii, M. and Showkati, H. (2012). "Experimental investigation on cyclic behavior of perforated steel plate shear walls", Journal of Constructional Steel Research, 70, 308-316. Vian, D. (2005). Steel plate shear walls for seismic design and retrofit of building structures, State University of New York at Buffalo Vian, D., Bruneau, M. and Purba, R. (2009a). "Special perforated steel plate shear walls with reduced beam section anchor beams. II: Analysis and design recommendations", Journal of Structural Engineering, 135, 221-228. Vian, D., Bruneau, M., Tsai, K.-C. and Lin, Y.C. (2009b). "Special perforated steel plate shear walls with reduced beam section anchor beams, I: Experimental investigation", Journal of Structural Engineering, 135, 211-220.
| ||
|
آمار تعداد مشاهده مقاله: 539 تعداد دریافت فایل اصل مقاله: 489 |
||