سامانه پشتیبانی خدمات اطلاعات

  اخبار و اعلانات

 آمار

تعداد نشریات161
تعداد شماره‌ها6,532
تعداد مقالات70,502
تعداد مشاهده مقاله124,116,710
تعداد دریافت فایل اصل مقاله97,221,462
Izi, Ali, Honarpisheh, Mohammad, Ahmadi, Farshid. (1403). Non-uniform simple shear extrusion (NUSSE) technique as a novel sever plastic deformation technique. , 57(1), 9-18. doi: 10.22059/jufgnsm.2024.01.02
Ali Izi; Mohammad Honarpisheh; Farshid Ahmadi. "Non-uniform simple shear extrusion (NUSSE) technique as a novel sever plastic deformation technique". , 57, 1, 1403, 9-18. doi: 10.22059/jufgnsm.2024.01.02
Izi, Ali, Honarpisheh, Mohammad, Ahmadi, Farshid. (1403). 'Non-uniform simple shear extrusion (NUSSE) technique as a novel sever plastic deformation technique', , 57(1), pp. 9-18. doi: 10.22059/jufgnsm.2024.01.02
Izi, Ali, Honarpisheh, Mohammad, Ahmadi, Farshid. Non-uniform simple shear extrusion (NUSSE) technique as a novel sever plastic deformation technique. , 1403; 57(1): 9-18. doi: 10.22059/jufgnsm.2024.01.02

Non-uniform simple shear extrusion (NUSSE) technique as a novel sever plastic deformation technique

Journal of Ultrafine Grained and Nanostructured Materials
دوره 57، شماره 1، شهریور 2024، صفحه 9-18    اصل مقاله (1.11 M)
نوع مقاله: Research Paper
شناسه دیجیتال (DOI): 10.22059/jufgnsm.2024.01.02
نویسندگان
Ali Izi؛ Mohammad Honarpisheh* ؛ Farshid Ahmadi
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
چکیده
In this research, a new technique for severe plastic deformation (SPD) was proposed, entitled as non-uniform simple shear extrusion (NUSSE). The larger strains can be obtained in the non-uniform simple shear extrusion (NUSSE) method without repetition of the process. But, in pure shear extrusion (PSE) and simple shear extrusion (SSE) processes, to achieve larger strains, it is necessary to repeat the processes. In this study, the technique was investigated experimentally and numerically using ABAQUS software. The maximum plastic strain, inhomogeneity in deformation, filling fraction and micro-hardness parameters were researched after NUSSE process. Also, the obtained results were compared to the SSE and PSE processes. After this technique, due to the specific design of deformation channel, filling fraction was increased by about 44.92% and 41.84% in comparison with SSE and PSE processes, respectively. Also, the micro-hardness was significantly increased compared to annealing process.
کلیدواژه‌ها
Sever plastic deformation؛ Non-Uniform Simple Shear Extrusion؛ Filling fraction؛ Inhomogeneity in deformation؛ Micro-hardness
مراجع
  1. Bayat Tork N, Saghafian H, Razavi SH, Al-Fadhalah KJ, Ebrahimi R, Mahmudi R. Microstructure and texture characterization of Mg–Al and Mg–Gd binary alloys processed by simple shear extrusion. Journal of Materials Research and Technology. 2019;8(1):1288-99.
  2. Horita Z. Nanomaterials by Severe Plastic Deformation. Materials Science Forum: Trans Tech Publications Ltd; 2006.
  3. Valiev RZ, Estrin Y, Horita Z, Langdon TG, Zechetbauer MJ, Zhu YT. Producing bulk ultrafine-grained materials by severe plastic deformation. JOM. 2006;58(4):33-9.
  4. Azushima A, Kopp R, Korhonen A, Yang DY, Micari F, Lahoti GD, et al. Severe plastic deformation (SPD) processes for metals. CIRP Annals. 2008;57(2):716-35.
  5. Khanlari H, Honarpisheh M. An upper bound analysis of channel angular pressing process considering die geometric characteristics, friction, and material strain-hardening. CIRP Journal of Manufacturing Science and Technology. 2023;41:259-76.
  6. Khanlari H, Honarpisheh M. Investigation of Microstructure, Mechanical Properties and Residual Stress in Non-equal-Channel Angular Pressing of 6061 Aluminum Alloy. Transactions of the Indian Institute of Metals. 2020;73(5):1109-21.
  7. Aghababaei A, Honarpisheh M. Experimental and numerical investigation of residual stress distribution in Al-6061 tubes under using tubular channel angular pressing process by new trapezoidal channel. The Journal of Strain Analysis for Engineering Design. 2022;58(4):332-42.
  8. Moazam MA, Honarpisheh M. Improving the mechanical properties and reducing the residual stresses of AA7075 by combination of cyclic close die forging and precipitation hardening. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications. 2020;235(3):542-9.
  9. Moazam MA, Honarpisheh M. The effects of combined cyclic close die forging and aging process on microstructure and mechanical properties of AA7075. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications. 2020;234(9):1242-51.
  10. Moazam MA, Honarpisheh M. Ring-core integral method to measurement residual stress distribution of Al-7075 alloy processed by cyclic close die forging. Materials Research Express. 2019;6(8):0865j3.
  11. Zhilyaev AP, Langdon TG. Using high-pressure torsion for metal processing: Fundamentals and applications. Progress in Materials Science. 2008;53(6):893-979.
  12. Eivani AR, Rahimi F. Inhomogeneity in deformation, microstructure, tensile properties and damage development in AA1050 during multiple cycles of pure shear extrusion. Materials Science and Engineering: A. 2019;745:159-67.
  13. Beygelzimer Y, Varyukhin V, Synkov S, Orlov D. Useful properties of twist extrusion. Materials Science and Engineering: A. 2009;503(1-2):14-7.
  14. Pardis N, Ebrahimi R. Deformation behavior in Simple Shear Extrusion (SSE) as a new severe plastic deformation technique. Materials Science and Engineering: A. 2009;527(1-2):355-60.
  15. Nazari F, Honarpisheh M. Analytical model to estimate force of constrained groove pressing process. Journal of Manufacturing Processes. 2018;32:11-9.
  16. Nazari F, Honarpisheh M, Zhao H. Effect of stress relief annealing on microstructure, mechanical properties, and residual stress of a copper sheet in the constrained groove pressing process. The International Journal of Advanced Manufacturing Technology. 2019;102(9-12):4361-70.
  17. Kotobi M, Honarpisheh M. Uncertainty analysis of residual stresses measured by slitting method in equal-channel angular rolled Al-1060 strips. The Journal of Strain Analysis for Engineering Design. 2016;52(2):83-92.
  18. Honarpisheh M, Haghighat E, Kotobi M. Investigation of residual stress and mechanical properties of equal channel angular rolled St12 strips. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications. 2016;232(10):841-51.
  19. Bagherpour E, Qods F, Ebrahimi R, Miyamoto H. Strain reversal in simple shear extrusion (SSE) processing: Microstructure investigations and mechanical properties. AIP Conference Proceedings: Author(s); 2018.
  20. Sedehi SMR, Khosravi M, Yaghoubinezhad Y. Mechanical properties and microstructures of reduced graphene oxide reinforced titanium matrix composites produced by spark plasma sintering and simple shear extrusion. Ceramics International. 2021;47(23):33180-90.
  21. Pardis N, Ebrahimi R. Different processing routes for deformation via simple shear extrusion (SSE). Materials Science and Engineering: A. 2010;527(23):6153-6.
  22. Tork NB, Pardis N, Ebrahimi R. Investigation on the feasibility of room temperature plastic deformation of pure magnesium by simple shear extrusion process. Materials Science and Engineering: A. 2013;560:34-9.
  23. Bagherpour E, Reihanian M, Ebrahimi R. On the capability of severe plastic deformation of twining induced plasticity (TWIP) steel. Materials & Design (1980-2015). 2012;36:391-5.
  24. Ebrahimi R, Rezvani A, Bagherpour E. Circular simple shear extrusion as an alternative for simple shear extrusion technique for producing bulk nanostructured materials. Procedia Manufacturing. 2018;15:1502-8.
  25. Rezvani A, Bagherpour E, Ebrahimi R. Circular Simple Shear Extrusion as an Alternative to Simple Shear Extrusion Technique. Iranian Journal of Science and Technology, Transactions of Mechanical Engineering. 2018;44(1):193-201.
  26. Rezvani, A., Ebrahimi, R. Investigation on the Deformation Behavior and Strain Distribution of Commercially Pure Aluminum after Circular Simple Shear Extrusion. Journal of Ultrafine Grained and Nanostructured Materials, 2019; 52(1): 32-42.
  27. Bay N. Friction stress and normal stress in bulk metal-forming processes. Journal of Mechanical Working Technology. 1987;14(2):203-23.
  28. Djavanroodi F, Daneshtalab M, Ebrahimi M. A novel technique to increase strain distribution homogeneity for ECAPed materials. Materials Science and Engineering: A. 2012;535:115-21.
  29. Rahimi F, Eivani AR, Kiani M. Effect of die design parameters on the deformation behavior in pure shear extrusion. Materials & Design. 2015;83:144-53.
  30. Bagherpour E, Qods F, Ebrahimi R. Effect of geometric parameters on deformation behavior of simple shear extrusion. IOP Conference Series: Materials Science and Engineering. 2014;63:012046.
  31. Sedehi SMR, Khosravi M, Yaghoubinezhad Y. Mechanical properties and microstructures of reduced graphene oxide reinforced titanium matrix composites produced by spark plasma sintering and simple shear extrusion. Ceramics International. 2021;47(23):33180-90.
  32. Rahimi F, Eivani AR. A new severe plastic deformation technique based on pure shear. Materials Science and Engineering: A. 2015;626:423-31.
  33. Bagherpour E, Reihanian M, Ebrahimi R. Processing twining induced plasticity steel through simple shear extrusion. Materials & Design. 2012;40:262-7.
 

 

آمار
تعداد مشاهده مقاله: 296
تعداد دریافت فایل اصل مقاله: 135


سامانه مدیریت نشریات علمی. قدرت گرفته از سیناوب