|تعداد مشاهده مقاله||103,412,813|
|تعداد دریافت فایل اصل مقاله||81,412,762|
Cuttings Transport Modeling in Wellbore Annulus in Oil Drilling Operation using Evolutionary Fuzzy System
|Journal of Chemical and Petroleum Engineering|
|مقاله 8، دوره 54، شماره 2، اسفند 2020، صفحه 273-283 اصل مقاله (922.23 K)|
|نوع مقاله: Research Paper|
|شناسه دیجیتال (DOI): 10.22059/jchpe.2020.297247.1307|
|Reza Rooki 1؛ Seyed Mohammad Reza Kazemi2؛ Esmaeil Hadavandi2؛ Seyed Mahmood Kazemi2|
|1Department of Mining, Civil and Chemical Engineering, Birjand University of Technology, Birjand, Iran|
|2Department of Computer and Industrial Engineering, Birjand University of Technology, Birjand, Iran|
|A difficult problem in drilling operation that concerns the very drilling parameters is the cutting transport process. Correct calculation of the cuttings concentration (hole cleaning efficiency) in the wellbore annulus using drilling variables such as the geometry of wellbore, rheology, and density of drilling fluid, and pump rate is very important for optimizing these variables. In this study, a hybrid evolutionary fuzzy system (EFS) using artificial intelligent (AI) techniques is presented for estimation of the cuttings concentration in oil drilling operation using operational drilling parameters. A well-organized genetic learning algorithm that computes fitness values by symbiotic evolution is used for extraction of the Takagi–Sugeno–Kang (TSK) type fuzzy rule-based system for the EFS. A determination coefficient (R2) of 0.877 together with a root mean square error (RMSE) of 1.4 between prediction and measured data for test data verified a very satisfactory model performance. Results confirmed that the estimation accuracy of the proposed EFS is better than other models such as Multiple Linear Regression (MLR), artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) for hole cleaning modeling.|
|Artificial Intelligent Methods؛ Drilling؛ EFS؛ Hole Cleaning؛ Wellbore|
 Larsen TI, Pilehvari AA, Azar JJ. Development of a new cuttings-transport model for high-angle wellbores including horizontal wells. SPE Drilling & Completion. 1997 Jun 1;12(02):129-36.
 Tomren PH, Iyoho AW, Azar JJ. Experimental study of cuttings transport in directional wells. SPE Drilling Engineering. 1986 Feb 1;1(01):43-56.
 Mirhaj SA, Shadizadeh R, Fazaeli-zadeh M. Cuttings removal simulation for deviated and horizontal wellbores. InSPE Middle East Oil and Gas Show and Conference 2007 Mar 11.
 Bourgoyne Jr AT, Millheim KK, Chenevert ME, Young Jr FS. Applied drilling engineering chapter 8 solutions.
 Rooki R, Ardejani FD, Moradzadeh A. Hole cleaning prediction in foam drilling using artificial neural network and multiple linear regression. Geomaterials. 2014 Jan 9;2014.
 Rooki R, Ardejani FD, Moradzadeh A, Norouzi M. CFD simulation of rheological model effect on cuttings transport. Journal of Dispersion Science and Technology. 2015 Mar 4;36(3):402-10.
 Duan, M., 2007. Study of Cuttings Transport Using Foam with Drill Pipe Rotation under Simulated Downhole Conditions, PhD Dissertation, Tulsa University, USA.
 Chen Z. Cuttings transport with foam in horizontal concentric annulus under elevated pressure and temperature conditions. The University of Tulsa; 2005.
 Ozbayoglu, M.E., 2002. Cuttings transport with foam in horizontal and highly-inclined wellbores, PhD Dissertation, University of Tulsa, USA.
 Rojas Y, Vieira P, Borrell M, Blanco J, Ford M, Nieto L, Lopez G, Atencio B. Field application of near-balanced drilling using aqueous foams in western Venezuela. InIADC/SPE Drilling Conference 2002 Jan 1. Society of Petroleum Engineers.
 Suradi SR, Mamat NS, Jaafar MZ, Sulaiman WR, Ismail AR. Study of cuttings transport using stable foam based mud in inclined wellbore. J. Appl. Sci.. 2015 Mar 1;15(5):808.
 He M, Zhang Y, Xu M, Li J, Song J. Real-Time Interpretation Model of Reservoir Characteristics While Underbalanced Drilling Based on UKF. Geofluids. 2020 May 19;2020.
 Okpobiri GA, Ikoku CU. Volumetric requirements for foam and mist drilling operations. SPE Drilling Engineering. 1986 Feb 1;1(01):71-88.
 Guo, B., Miska, S., and Hareland, G., 1995. A simple approach to determination of bottom hole pressure in directional foam drilling, ASME Drilling Technology Symposium, PD-Vol. 65: 329-338.
 STAINTPERE S. Hole Cleaning Capabilities of Drilling Foams Compared to Conventional Fluids. Inpresented at the 2000 SPE Annual Technical Conference and Exhibitions, Dallas-Texas 2000.
 Li Y, Kuru E. Numerical modelling of cuttings transport with foam in horizontal wells. Journal of Canadian Petroleum Technology. 2003 Oct 1;42(10).
 Li, Y., Kuru, E., 2005, Numerical modeling of cuttings transport with foam in vertical wells, Journal of Canadian Petroleum Technology 44(3): 31-39.
 Martins, A.L., Luorenco, A.M.F de Sa, C.H.M., 2001. Foam properties requirements for proper hole cleaning while drilling horizontal wells in underbalanced conditions, SPE Drill & Completion 16 (4): 195-200.
 Capo, J., Yu, M., and Miska, S. Z., Takach, N.E., Ahmed, R., 2006. Cuttings transport with aqueous foam at intermediate inclined wells [C], SPE Drilling and Completion 21(2):99–107.
 Arya A, Liang X, Von Solms N, Kontogeorgis GM. Modeling of asphaltene onset precipitation conditions with cubic plus association (CPA) and perturbed chain statistical associating fluid theory (PC-SAFT) equations of state. Energy & Fuels. 2016 Jul 26;30(8):6835-52.
 Chen Z, Ahmed RM, Miska SZ, Takach NE, Yu M, Pickell MB, Hallman JH. Experimental study on cuttings transport with foam under simulated horizontal downhole conditions. SPE Drilling & Completion. 2007 Dec 1;22(04):304-12..
 Yan T, Wang K, Sun X, Luan S, Shao S. State-of-the-art cuttings transport with aerated liquid and foam in complex structure wells. Renewable and Sustainable Energy Reviews. 2014 Sep 1;37:560-8.
 Hadavandi E, Shavandi H, Ghanbari A, Abbasian-Naghneh S. Developing a hybrid artificial intelligence model for outpatient visits forecasting in hospitals. Applied Soft Computing. 2012 Feb 1;12(2):700-11.
 Braunschweig, B., Bremdal B.A. 1996, Artificial intelligence in the petroleum industry: symbolic and computational applications. Volume 2, Editions TECHNIP, Technology & Engineering - 381 pages.
 Rooki R. Application of general regression neural network (GRNN) for indirect measuring pressure loss of Herschel–Bulkley drilling fluids in oil drilling. Measurement. 2016 May 1;85:184-91.
 Bello O, Holzmann J, Yaqoob T, Teodoriu C. Application of artificial intelligence methods in drilling system design and operations: a review of the state of the art. Journal of Artificial Intelligence and Soft Computing Research. 2015 Apr 1;5(2):121-39.
 Cranganu C, Luchian H, Breaban ME, editors. Artificial intelligent approaches in petroleum geosciences. Berlin: Springer; 2015 Apr 18.
 Al-Azani K, Elkatatny S, Ali A, Ramadan E, Abdulraheem A. Cutting concentration prediction in horizontal and deviated wells using artificial intelligence techniques. Journal of Petroleum Exploration and Production Technology. 2019 Dec 1;9(4):2769-79.
 Ouaer H, Gareche M, Rooki R. Rheological studies and optimization of Herschel–Bulkley parameters of an environmentally friendly drilling fluid using genetic algorithm. Rheologica Acta. 2018 Nov 1;57(11):693-704.
 Cord O. Genetic fuzzy systems: evolutionary tuning and learning of fuzzy knowledge bases. World Scientific; 2001.
 Herrera F. Genetic fuzzy systems: taxonomy, current research trends and prospects. Evolutionary Intelligence. 2008 Mar 1;1(1):27-46.  Kazemi SM, Hadavandi E, Mehmanpazir F, Nakhostin MM. A hybrid intelligent approach for modeling brand choice and constructing a market response simulator. Knowledge-Based Systems. 2013 Mar 1;40:101-10.
 Herrera F, Lozano M, Verdegay JL. A learning process for fuzzy control rules using genetic algorithms. Fuzzy sets and systems. 1998 Nov 16;100(1-3):143-58.
 Juang CF, Lin JY, Lin CT. Genetic reinforcement learning through symbiotic evolution for fuzzy controller design. IEEE Transactions on Systems, Man, and Cybernetics, Part B (Cybernetics). 2000 Apr;30(2):290-302.
 Shahrabi J, Hadavandi E, Asadi S. Developing a hybrid intelligent model for forecasting problems: Case study of tourism demand time series. Knowledge-Based Systems. 2013 May 1;43:112-22.
 Eiben ÁE, Hinterding R, Michalewicz Z. Parameter control in evolutionary algorithms. IEEE Transactions on evolutionary computation. 1999 Jul;3(2):124-41.
تعداد مشاهده مقاله: 461
تعداد دریافت فایل اصل مقاله: 480